<delect id="ppfbv"><video id="ppfbv"></video></delect>

          <ins id="ppfbv"><em id="ppfbv"></em></ins>

          <font id="ppfbv"></font>

          全自動KN95口罩機

          • 型號:

            YD-QZDKN95-001
          • 產品別稱:

            KN95口罩,耳掛式KN95口罩機,口罩機生產線
          • 主要組成部分:

            打片機、焊耳機
          • 現貨:

          • 速度:

            40pcs/min

          同類產品推薦

          • 全自動KF94口罩機
          • 平面一拖一口罩機
          • 平面焊耳機
          • KN95焊耳機

          139-2940-8368

          180-2515-1739

          • 產品詳情

           

           

           
           
          生產節拍 :40±5pcs/min
          機臺功率 :最大功率20KW
          (超音波2.6KW*2 + 2KW*2 + 設備其他10.8KW)
          氣源:壓縮空氣要穩定在0.5Mpa以上
          直徑12的氣管:接三聯件,預留2個接口
          電源:220V  16A
          外形尺寸mm:9800(L)*1400(W)*2000(H)
           
          Production cycle: 40±5pcs/min
          Machine power: maximum power 20KW
          (Ultrasonic 2.6KW*2 + 2KW*2 + other equipment 10.8KW)
          Air source: compressed air should be stabilized above 0.5Mpa
          Trachea with a diameter of 12: connect to the triple piece, and reserve 2 ports
          Power supply: 220V 16A
          Dimensions mm: 9800(L)*1400(W)*2000(H)
           
           
          KN95口罩機由以下設備組成:六層原材料上料機構、鼻梁&壓紋工序、焊接耳帶工序、打碼(根據需求選配噴碼或者激光打標)、成本裁切&廢料處理工序。
           
          The KN95 mask machine consists of the following equipment: six-layer raw material feeding mechanism, nose bridge & embossing process, welding ear strap process, coding (optional inkjet or laser marking according to requirements), cost cutting & waste treatment process.
           
          設備動作流程:1、原材料上料(根據產品要求放置四層布料或五層布料)→推鼻梁條→本體滾花→左耳帶焊接→右耳帶焊接→打碼(根據需求選配噴碼或者激光打標)→折邊→封邊→成本裁切→成品排出
          Equipment action process: 1. Raw material loading (place four or five layers of fabric according to product requirements) → push nose bridge → body knurling → left ear band welding → right ear band welding → coding (optional coding according to requirements Or laser marking) → folding → edge banding → cost cutting → finished product discharge
           
          安裝要求
          1、檢查地面的承受力和平整度,綜合考慮機器的總重量和機器在運轉時引起的振動。
          2、水平放置機器,調整各機腳使其處于水平狀態。
          3、接通電源之前,仔細檢查各連接是否松動。
          4、正確連接電源。
          5、需要的電源為AC 220V /50Hz。
          Installation requirements
          1. Check the bearing capacity and flatness of the ground, comprehensively consider the total weight of the machine and the vibration caused by the machine during operation.
          2. Place the machine horizontally and adjust the feet of each machine to make it level.
          3. Before turning on the power, carefully check whether the connections are loose.
          4. Connect the power supply correctly.
          5. The required power supply is AC 220V/50Hz.
           
          設備維護
          設備的日常維護和保養是保證設備運行良好,降低故障發生率和提高設
          備使用壽命的有效手段??蛻粼谑褂迷O備進行生產活動時,應特別予以重視。
          1、操作人員在操作設備的過程中,應密切注意設備的運轉情況,做好設備運轉記錄,詳細記錄本班設備的運轉情況,供設備維護人員在檢查和維護設備時參考。
          2、發現異常,必須馬上停機,通知維修人員處理,故障排除后方可重新開機。
          3、設備維護人員應對設備進行定期的檢查、維護和保養。
          4、保養設備前,必須先斷開電源,并遵守相關安全規范。
          5、任何固定的保護裝置因保養需要打開或者移走,保養完畢后,必須完整無損地回復原位。
          Equipment maintenance
          The daily maintenance of the equipment is to ensure that the equipment is running well, reduce the failure rate and improve the equipment.
          Effective means to prepare the service life. Customers should pay special attention when using equipment for production activities.
          1. In the process of operating the equipment, the operator should pay close attention to the operation of the equipment, make a record of the equipment operation, and record the operation of the equipment in the class in detail for the equipment maintenance personnel to refer to when inspecting and maintaining the equipment.
          2. If an abnormality is found, the machine must be shut down immediately, and the maintenance personnel must be notified to deal with it, and the machine can be restarted after the fault is eliminated.
          3. The equipment maintenance personnel shall conduct regular inspection, maintenance and maintenance of the equipment.
          4. Before servicing the equipment, you must disconnect the power supply and follow the relevant safety regulations.
          5. Any fixed protection device needs to be opened or removed due to maintenance. After maintenance, it must be restored to its original position intact.

           

          標簽:  KN95口罩機
          分享到:
          国产超级乱婬视频播放,国产成a人片在线关看视频,国产成a人片在线观看网站,国产成人18禁在线播放,国产成人5g影院无码网站